Agricultural and Biosystems Mechanization, Planning, Operation, Maintenance, Management, Manufacturing Practice Test

These questions are part of the practice quiz. Start practicing

• What term describes the power available at the drawbar sustained over a distance of at least 20 meters?
• Which term refers to the quality of material used and the manufacturing technology in the production of a tractor?
• Decide if you need an engine or electric motor is best described as choosing what?
• What is the left hydraulic arm of the three-point hitch used for hooking up implements?
• What is the term for the point of equal weight distribution, where about half the weight lies in front of it and half behind?
• Which adjustment angle is the angle the disc makes with the direction of travel to control width and allow rotation?
• Which instrument indicates the hours the tractor has been used and includes a digit for tenths of an hour?
• Which term refers to processes that cause molten molding material to enter a mold where it solidifies before being extracted?
• Which capacity configuration is described as best for efficiency and sustained production when using a single, large machine?
• Which control is used to engage/disengage the PTO shaft?
• Used to cut metals, wood, or other materials into desired shapes.
• it will turn on when the battery is not charging
• Which process is primarily concerned with decorating or protecting a surface by coating or converting its properties?
• Its mission is to work the development of a progressive and dynamic metal working sector that can firmly stand as the backbone of the industry.
• Which term describes removing material to achieve size and shape?
• Which hazard results when another material gets caught and wrapped around a PTO shaft, especially when the PTO is unshielded?
• The AFMESC shall be strategically located in agricultural and fishery production areas of the country, with what minimum distribution requirement?
• Which tillage operation pulverizes and smoothens the soil to a depth of 3-6 inches?
• What term describes the overall process of preparing parts and putting them together to form a complete product?
• Which gauge indicates the coolant temperature and uses C for cold and H for hot?
• Which term would include protective seals and surface hardening as part of enhancing a surface?
• Which small tractor is commonly used in small farm areas like a garden?
• Which term describes the pin that connects the upper and lower link to the tractor?
• Which device starts or stops the engine?
• Which lever provides the gear shifting in an H-pattern from 1 to 4 gears plus neutral?
• Used to hold or secure workpieces during manufacturing.
• Which consideration refers to the number and type of trainings attended by staff and members, additional training, manpower requirement, salary and benefits, among others?
• Which control disengages the transmission clutch when pressed fully?
• Which lever moves the range gear through HIGH, LOW, and Reverse?
• In a field with loamy to clay soil and embankments enabling flooding, which soil preparation type is appropriate?
• Capable to operate and produce agricultural machine by batch and do mass production of small machines if ever needed; More equipment and facilities; Special process needed to manufacture a certain machine is done by subcontracting to other machine shops.
• Which tractor component provides comfort to the operator?
• A description of agricultural tractors, self-propelled machines, implements, and combinations thereof designed primarily for agricultural field operations is best described as what term?
• What is the current mechanization level in the Philippines (2025) in hp/ha?
• Four-wheel tractors with available power exceeding 45 horsepower are classified as which type?
• Which part is used to level the three-point mounted implement side to side by turning the adjustable handle with the implement on the ground?
• If exhaust fumes are blue-white, which issue is most likely?
• The level of agricultural mechanization in the Philippines is commonly measured in terms of:
• Which component is not a typical part of a three-point linkage assembly?
• Which color indicates a failure or serious malfunction requiring immediate attention?
• Which term denotes the trench or canal left by the furrowslice?
• Which description best characterizes AFMESC?
• Which term refers to a configuration used to transmit power from a driver shaft to a driven shaft?
• Which part provides a signal light in front when turning left or right?
• What is the name of the common service facility equipped with agricultural machinery and located within SAFDZs and ARCs and operated as a business?
• Bevel gears whose teeth are straight but the sides are tapered so that they would intersect the axis at a pitch cone apex if extended inward are called?
• Which administrative order governs AFMESC?
• Which process is primarily about fitting components together to create a larger structure?
• Which control sets the speed of lowering the three-point hitch for attaching an implement?
• Which gauge indicates engine speed and the 540 PTO shaft speed location on the dial?
• A traction machine intended primarily for off-road usage, designed to supply power to agricultural implements, is known as which?
• Which device keeps the tractor stationary when parked?
• What is the trench or canal left by the furrowslice called?
• Which component facilitates easy steering of the machine toward the right or left?
• Which tractor type has greater ground clearance and can straddle taller crops?
• Which category of four-wheel tractors is defined by a power range of approximately 15 to 25 horsepower?
• Which category is described as machines that generate labor by increasing cropping intensities and enabling full utilization of farm products and by-products?
• Which of the following is NOT listed as a benefit of mechanization under the RCEF?
• Which term refers to equipment used to provide mechanical or electrical power to perform machining tasks?
• If the engine is difficult to start or won’t start, which step is recommended first?
• Which category of tools is used to cut metals, wood, or other materials into desired shapes?
• Which tillage is described as the combination of plowing and harrowing, with depth up to 6 inches?
• Which feature refers to the placement of controls, ensuring that controls are accessible and easy to operate?
• Which option is described as providing an arrangement to protect the driver during rollover?
• Pin that connects the upper/lower link to the tractor
• Which general category encompasses painting, plating, and chemical treatments to alter surface properties?
• It is composed of members engaged in the manufacture, assembly, distribution, and servicing of agricultural machinery to promote farm mechanization and adoption of modern field practices in the country.
• What is the objective of the Agricultural and Fisheries Mechanization Law (RA 10601 of 2012)?
• Which part of a three-point hitch is primarily used to mount the implement and raise it?
• Which term is associated with smoothing, polishing, or surface preparation?
• Two-post structural frames are primarily used to protect a seat-belted operator from being crushed in case the machine rolls over. Which of the following is the correct description?
• What is the external shaft at the rear of the tractor providing rotational power to implements?
• What term describes the apparent outward force on a body moving in a circular path, such as a spike-tooth harrow?
• Which term describes the component that provides rotational power to implements and is located at the rear of the tractor?
• Which term refers to the parts and services provided by manufacturers, distributors, and dealers to end-users to ensure the continuous serviceability of agricultural machinery?
• Which factors affect the base of stability of a tractor?
• What percent reduction in greenhouse gas (GHG) pollutants is associated with mechanization under the RCEF?
• What is the name of the wheel having flat or crowned face used to transmit motion and power by means of flat belts?
• The Farm and Fisheries Clustering and Consolidation program is abbreviated as F2C2 and focuses on clustering and consolidation up to which stage?
• Which component directs the steering of the front axle?
• A self-propelled machine, two-axle vehicle with 48 to 58 hp used for plowing, harrowing, and transporting goods is best described as which of the following?
• Before using the four-wheel drive system (4WDT), it is advisable to consider what is called?
• In what year was the AMDPC inaugurated?
• A mechanical device designed to hold, join, or maintain equilibrium of components is called a?
• What term describes processes used to temporarily or permanently fasten or bond pieces together?
• Which tillage operation includes subsequent breaking, pulverization and leveling of the soil making it ready for planting, with a depth of 3-6 inches?
• Which term best describes the stage where parts are connected to create subassemblies or final products?
• Tractors classified by available power between 15 and 25 horsepower are called what?
• Which term is used for the process of preparing soil to provide favorable environment for germination and growth?
• Which type of tractor has a traditional design and is built closer to the ground?
• Which lever keeps the tractor stationary when parked?
• In selecting agricultural machinery, which feature refers to the quality of material used and the manufacturing technology employed, impacting performance and durability?
• What is the term for the assembly that connects implements to the tractor using three links?
• Which term is used for the acts of joining components through fasteners, adhesives, or mechanical bonds to form a product?
• Which label indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury?
• Which control turns the headlights on or off?
• Connect machinery parts and allow for easy assembly and disassembly is the function of a?
• The AMDPC is the result of a partnership between the Department of Agriculture through PHilMech and which international agency?
• Which label indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury?
• Which indicator lights when the engine is being preheated?
• Which category of agricultural machines directly replaces human labor?
• What action is recommended when the tractor engine starts but runs roughly?
• When backing a tractor with a trailer, once the trailer is moving rightward, should the steering wheel be kept to the right until the trailer stops moving?
• On slow-moving machines with a maximum design speed, the SMV emblem shall be used for speeds up to what?
• Which component is used to secure the bracket on the center of the rear transmission housing?
• What is the name of the modified version of the Agricultural Mechanization Index?
• Which component provides traction for four-wheel drive tractors and bears the full weight of the front side of a tractor?
• Which control is a foot-operated regulator of engine power and speed, used on the road for higher speed?
• Which accessory is used to hold the operator's cup or tumbler?
• Which term is used for smoothing, polishing, or surface preparation?
• The Agricultural and Fisheries Modernization Act requires identifying which zones?
• What refers to business enterprises owned and operated by private entities, individual farmers, or groups of farmers that provide machinery custom services and other farm-related services?
• Which component is used to move gear wheels relative to each other and has an H-shaped pattern from 1-4 gears and neutral?
• Articulated connection between a link and the implement
• Which document contains the Implementing Guidelines in the Establishment, Operation, Maintenance and Management of Agri-Fishery Machinery and Equipment Service Centers (AFMESCs)?
• Which term describes processes that change material properties using heat, pressure, or chemical action?
• Capable of mass producing agricultural machines because they almost complete line of equipment needed in manufacturing; Small and medium manufacturers sometimes subcontracting to this class.
• Which term refers to agri-fisheries workers who have achieved all the required units of competency of a national qualification defined under TESDA Training Regulations and conferred with a National Certificate on a particular qualification in the agrifisheries mechanization sector?
• What is the name of the hitch that uses one upper link and two lower links to connect an implement to the tractor?
• Which term is the alternate name for 'Harrowing'?
• Which term refers to activities that join parts, such as bolting or welding, to form a larger unit?
• What happens when the center of gravity of a tractor is displaced outside its base of stability?
• indicates the fuel level when the key switch is on
• Which tractor is modified to reduce the possibility of tree limbs catching?
• Three-point linkage category for a maximum drawbar power of 15 to 35 kW.
• What term describes processes that protect or beautify a surface by converting the surface or applying a coating?
• Which component bears the full weight of the back side of a tractor?
• AFMESC stands for what?
• Which term refers to the output power measured at the PTO shaft?
• Which agency is responsible for Rice Extension Services and postharvest development and mechanization, among the agencies listed?
• Three-point linkage category for a maximum drawbar power of 30 to 75 kW.
• The Rice Competitiveness Enhancement Fund (RCEF) is also known by what alternate name?
• Which control sounds the horn when pressed?
• Which category of agricultural machines is defined as those that enable tasks not possible with available animal and human labor?
• Which term describes making a product by changing the shape, size, or composition of materials?
• A tractor's three-point hitch category for a maximum drawbar power of 60 to 168 kW corresponds to which category?
• Which control engages/disengages the front wheel drive?
• Under the Rice Competitiveness Enhancement Fund, which figure represents the reported reduction in production cost per hectare due to mechanization?
• In soil management, which term describes the process of preparing soil to provide favorable soil environment for plant germination and growth?
• Which term describes processes that apply a protective or decorative coating to surfaces?
• Which term describes tillage for unplowed soil?
• This feature ensures spare parts and service are available nearby?
• Which runover incident occurs when a passenger (extra rider) on a tractor falls off because there is only one safe place for a person to be on the tractor?
• Which color represents normal operating conditions?
• What is the typical disc angle range?
• Which term refers to the level of mechanization that encompasses science, technology, infrastructure, policies, and innovations?
• Which component functions as the primary mounting point for towing implements behind the tractor?
• What is the typical tilt angle range for proper soil penetration?
• Which soil preparation type is suited for limited water, limited labor, sandy soil, and a well-established hard pan?
• Used to lay out lines, points, or patterns before cutting or machining.
• Which term describes the symbol used to warn of safety-critical information on the machine?
• Which check ensures safety provisions for both machine and operator?
• Which term describes processes that cause molten molding material to enter a mold where it solidifies before being extracted?
• What percentage reduction in postharvest losses is attributed to mechanization under the RCEF?
• Which term describes bevel gears whose teeth are straight but the sides are tapered so that they would intersect the axis at a pitch cone apex if extended inward?
• What is the trench left equal to two furrows when furrowslices are thrown on opposite sides?
• Which entity is described as Philippine-based, foreign or Filipino-owned, and involved in the production and distribution of agricultural machinery?
• Which control stops the wheels when left and right are pressed at the same time?
• Which part is associated with signaling for turns or hazards?
• What document is used to determine the viability of a project for obtaining a loan or grant, including recovering investment costs and repayment on an amortized schedule?
• In manufacturing, which term includes actions such as welding, riveting, and adhesive bonding to join components?
• Which label indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury?
• In selecting agricultural machinery, which feature refers to the reputation of the manufacturer and a guarantee of what lies beneath the paint?
• Which agency focuses on rice research and development, including rice variety development?
• Which type is designed to operate in tight spaces between rows of crops?
• What term describes the system of production using tools, implements, and machines for agricultural land development, production, harvesting, and on-farm processing?
• Which lamp turns on if the engine oil pressure goes below the prescribed level?
• it will turn on if the oil pressure goes below prescribed level
• What pedal is used to synchronize the rotation of the rear wheels if one rear wheel slips?
• Which term refers to devices used to bend, shape, or form materials into desired configuration?
• In dismounting a three-point linkage implement, which link should be detached first?
• Which soil management practice is described as cultivation with minimal soil disturbance, exemplified by the strip-till method?
• Which tillage system is used for unplowed soil?
• Which category includes tractors with tires designed for use on hard surfaces?
• Which term denotes an expressed assurance of the quality of the materials and workmanship of products offered for sale?
• Which law liberalizes the importation, exportation, and trading of rice, lifting quantitative import restrictions?
• What is the primary function of the rotavator's cutting knives or tines?
• Which indicator shows if the turn signal or hazard light is on or off?
• For sandy soils with limited water and labor, which soil preparation type is most suitable?
• Which label corresponds to a hazard that could result in death or serious injury if not avoided?
• AMMDA stands for which organization?
• Which organization is described by the acronym MEAP and is associated with the metalworking sector?
• Which component is a toothed wheel that engages with chain links to transmit rotary motion and power between shafts?
• What does the tachometer indicate on the tractor dashboard?
• What is the name of the hitch pin designed to fit through the holes of the tractor drawbar and the implement tongue?
• What does the acronym AFMESC stand for?
• Which term describes a cylindrical gear with straight-line tooth traces parallel to the axis?
• Which term describes the reputation of the manufacturer and the guarantee of what lies beneath the paint?
• Which protective device prevents contact with the dangerous part from all sides?
• Which term indicates a hazard that may cause minor or moderate injury?
• Roll-Over Protective Structure is typically implemented using which frames?
• Which practice is described as mechanically altering some physical characteristics of the soil to be ideal for growing crops?
• A headed pin of metal used to unite two or more pieces by passing the shank through a hole in each piece and then by beating or pressing down the plain end so as to make a second head is called a?
• Which component is primarily used to stabilize the mounted implement and prevent sway?
• Which externally threaded fastener can mate with an internal thread or form its own thread and is tightened by torquing the head?
• Which irrigation system is identified as a priority project under AFMESCs?
• Which control engages/disengages the PTO shaft?
• MEAP stands for which organization?
• Which zones within NAPAAD are identified for production, agro-processing and marketing activities to help develop and modernize the agricultural and fisheries sectors in an environmentally and socio-cultural sound manner?
• AFMESCs primarily support operations in which sectors?
• What term refers to the tools, implements, and equipment used for field operations and postharvest, as well as for the establishment, care, and maintenance of agricultural products?
• Which item is used to store maintenance tools on the tractor?
• Before the Rice Tariffication Law was implemented in 2019, the mechanization level in the Philippine Rice Industry was approximately what? (2010)
• Which term denotes the specific application of tools/machines directly on the farm?
• Which component lights up the front of the tractor path?
• What is the universal symbol on the machine used to warn of possible personal injury?
• Which gear has teeth that trace as helices and transmits motion between two parallel axes?
• Which term covers implements and machines utilizing animal muscle as the power source?
• In a rotavator, which component holds the cutting knives or tines that rotate to slice soil?
• What term refers to a barangay or cluster of contiguous barangays with a critical mass of farmers or farm workers and which features the main thrust of agrarian development, land tenure improvement and delivery of support services?
• Which item is not a typical fastener used in machinery assemblies?
• The Agricultural Machinery Design and Prototyping Center is located at which organization?
• RA 11203 of 2019 refers to which policy?
• Which part bears the full weight of the back side of a tractor?
• Which term denotes the simplest and most basic level; use of tools and simple implements powered by human muscle?
• A business arrangement where two or more parties (e.g., farmers' cooperatives, private companies, or government agencies) combine resources, capital, or expertise to undertake a specific project or operation, while sharing risks, responsibilities, and benefits.
• Which Republic Act is known as the Agricultural and Fisheries Modernization Act of 1997?
• Used to measure dimensions and angles is which category?
• Which safety feature helps prevent the operator from falling or being thrown from the tractor?
• Which term describes processes that cause a material to take the shape of a die using an external force?
• turns hazard light on/off
• Protective device that uses a rail, fence, or frame to ensure a safety distance so the dangerous part cannot be reached inadvertently is called what?
• Classification of four-wheel tractors based on available power between 25 to 45 hp is called what?
• Which tractor is equipped with tires designed for use on hard surfaces?
• A modern farm mechanization practice that uses a laser-guided transmitter and receiver system attached to a tractor-drawn leveling blade to achieve a uniform, precise, and flat field surface.
• How is a rivet typically secured after it is inserted through holes in the pieces?
• Which device indicates in five digits the hours the tractor has been used and the last digit indicates 1/10 of an hour?
• Which feature focuses on the user's ease of operation and control activation?
• RA 10601 of 2012 is also known as which act?
• Its vision is to compete in the global industry.
• Which term describes implements powered by animal muscle?
• Protective device designed to prevent contact with the dangerous part from all sides is called what?
• Which pedal is used to equalize speed between rear wheels when traction is uneven?
• A machine designed with an integral power unit to provide mobility, tractive effort, and process power for performing agricultural operations is called what?
• What unit is used to measure the AFMESC minimum service area?
• When deciding between an engine and electric motor for powering a machine, what is the decision called?
• Which category is labeled as the highest category for agricultural machinery?
• Which control regulates engine power and speed by increasing and decreasing engine speed?
• Which term denotes the simplest level using tools powered by human muscle?
• What term refers to an authorized representative of distributors and/or manufacturers who supplies, trades, sells and services agricultural machinery to end-users?
• Which part provides traction and bears the full weight of the back side?
• Which category is designated for 15-35 kW maximum drawbar power?
• Which component has an internal thread and is designed to mate with the external thread on a bolt or screw?
• Which process is primarily concerned with beautifying or protecting surfaces rather than joining parts?
• Expanded rice credit assistance is managed by which financial institution?
• Which agency primarily provides training and extension services in agriculture nationwide?
• Which organization collaborates with the Bureau of Agricultural and Fisheries Engineering for the mobilization of AFMESCs?
• Which component protects from dirt and mud thrown by the wheel?
• Articulated connection between a link and the tractor
• What provides adding and releasing tension to the lower link to control the horizontal sway of the implement?
• This consideration refers to the status of operation, utilization and maintenance of farm machineries and facilities, including incidence of breakdowns and repairs.
• Which part of the three-point hitch adjusts the implement's angle by lengthening or shortening?
• This consideration refers to the financial report, administrative costs, current service areas and number of customers, existing services, target expansion, machinery rental fees and servicing rates, collection schemes, among others.
• Which practice involves cultivation with minimal physical change to the soil structure, such as the strip-till method?
• Which term describes soil cut, lifted, inverted and thrown to one side of the plow bottom?
• Which term describes the process of improving agriculture using mechanical power plus science, technology, infrastructure, policies, and innovations?
• Which component provides traction and bears the full weight of the back side of a tractor?
• Which component is a toothed wheel that engages with chain links to transmit rotary motion and power between shafts?
• Which term is listed as 'Deadfurrow' in the material?
• During mounting, which step requires aligning the left draft link with the hitch point of the implement and locking it with a hitch pin?
• it will turn on while engine is being preheated
• Which implement is constructed with cutting knives or tines on a horizontal power-driven shaft rotating at high speed to slice soil and pulverize it by centrifugal force?
• Which term covers processes that change material properties using heat, pressure, or chemical action?
• What is the raised ridge formed when two furrowslices overlap?
• Which model is described as aiming to cultivate a large area with limited manpower, corresponding to a high land area to farmer ratio?
• Protective devices designed to prevent contact with the dangerous part from the side or sides covered are called what?
• Which control disengages the transmission clutch when pressed halfway?
• What is the safest place for a person to be on a tractor according to safety guidelines?
• Which term describes the most sophisticated level of mechanization; agricultural machinery is powered by mechanical or non-animate sources of power?
• Roll-Over Protective Structure is designed primarily to protect the operator during which event?
• Which term refers to cultivation with no disturbance of the current soil condition prior to planting, hence the name?
• Which term best describes assembling functions like aligning, fitting, and fastening to build a mechanism?
• A small tractor modified to pass between narrow rows is known as which type?
• Which tillage operation is described as initial cutting, breaking and inversion of the soil, with depth 6-36 inches?
• Which statement best describes the function of a nut?
• Which agency shall serve as the overall coordinator and Program Management Office for the establishment, operation, maintenance and management of AFMESCs?
• Which control secures the operator by the seat belt?
• Which term is used for a farming approach that deliberately leaves soil undisturbed from harvest to planting?
• Which control selects the range gear through HIGH, LOW, and Reverse?
• What is the term for the power measured at the PTO shaft?
• An implement designed to perform agricultural field operations can be towed, mounted and semi-mounted. This describes which?
• What is the area inside the tractor where the wheels contact the ground, which varies with wheel spacing and axle-to-axle spacing?
• Which part serves as mounting for implements to be towed?
• Which term describes equipment used to provide mechanical or electrical power to perform machining tasks?
• Which term describes the entire system of production including tools, implements, and machines for land development, production, harvesting, and on-farm processing?
• Which category would include electroplating, anodizing, and varnishing as examples?
• Small manufacturing enterprises that are usually capable of manufacturing agricultural machines by piece only, often operating as backyard fabrication using common equipment such as hand saw, welding machines, and some power drill and sanders.
• If the coolant temperature gauge reaches the red zone, what does this indicate?
• Which term describes processes that give a material size and shape by removing excess material?
• Which term captures the primary purpose of providing a shield around rotating parts for safety?
• In AFMESCs, what is considered the main service provided?
• Which part bears the full weight of the front side and provides traction for four-wheel drive tractors?
• Which DA program encourages clustering and consolidation of farm operations up to marketing activities?
• What does AMDPC stand for?
• Which practice involves cultivation with minimal physical change to the soil structure, such as the strip-till method?
• Which term denotes the soil that is cut, lifted, inverted and thrown to one side by the plow bottom?
• NAPAAD stands for which phrase?
• Which symptom indicates poor fuel quality, too much oil, or a clogged air cleaner?
• Which fastener is externally threaded and designed for insertion through holes in assembled parts, tightened by a nut?
• Which control regulates engine speed via a hand lever?
• Which soil preparation method is characterized by access to a nearby water supply and embankments enabling flooding in loamy to clay soils?
• Which component is attached last in the mounting sequence?
• Laguna Agro-Industrial Machinery Manufacturers Association, Inc. (LAMMA) is best described as focusing on developing which sector?
• Which model is described as the low land-to-farmer ratio model?
• What is the mounting area of the front counterweight and hitch?
• Which term is described as equivalent to Secondary Tillage in the material?
• Which control turns the turn signals on or off?
• To promote mechanization of all aspects of agricultural industries by cooperating with the government; to work for central coordinating and training institute; to maintain liaison with local and foreign agencies in the promotion of mechanization; to apply and hold patent in the name of association.
• Which statement best describes the objective of AFMESC?
• Which component is used to direct the steering of the front axle?
• Which control secures the operator by the seat belt?
• Rice Extension Services agencies for farm schools nationwide include PHilMech, PhilRice, ATI, and TESDA. Which organization is NOT listed as part of these agencies?
• Which trading entity is authorized by foreign and local suppliers to distribute agricultural machinery to dealers?
• What is a common main cause when a tractor engine stops suddenly?
• Which component prevents the three-point hitch from swaying?
• Which cylindrical gear has straight teeth that run parallel to the gear axis and transmits motion between two axes?
• During mounting, which action describes aligning the drawbar with the hitch point of the implement?
• Which statement describes the first step in mounting a three-point linkage implement?
• If a farmer accomplishes 95% of plowing with a hand tractor and 5% with an animal-drawn plow, how is the level of mechanization classified?
• Which term describes gears whose teeth trace helices and transmit motion between parallel axes?
• Belts used to transmit rotary motion and power between two shafts, which lie flat on the face of its corresponding pulley, are called?
• What is the unbroken side of a furrow called?
• Which safety measure protects the operator from contact with moving parts?
• Which safety emblem is an important tractor emblem and is placed at the rear when the tractor is driven on public roads?
• Which step involves adjusting the top link at the center and aligning it with the hitch point of the implement?
• What term describes heavy-duty equipment for shaping, cutting, and finishing materials?
• Which protective device prevents contact with the dangerous part from the sides?
• Tilt angle is defined as the angle the disc makes with which reference to control soil penetration depth?
• What is the reported additional income per hectare from mechanization under the RCEF?
• Which term is used to join metals through heat or pressure?
• Which department issues the administrative order related to AFMESC?
• Which feature ensures that points of maintenance and adjustment are easy to perform?
• In starting a tractor engine, all levers should be in which position?
• What is described as another major tractor hazard involving a rider or an operator incident?
• A three-point hitch category for a maximum drawbar power of 135 to 300 kW corresponds to which category?
• Which component is used for keeping the operator's tools?
• When the engine won't start due to fuel issues, which of the following steps is recommended?
• Which term provides protection during manufacturing operations?
• Which sequence correctly represents the mounting order for a three-point linkage implement?
• Which component is described as 'lock of the hood' in the material?
• Which color is used to indicate outside normal operating limits?
• AFMESCs are located in which zones?
• Which item primarily enhances operator safety by restraining the operator in place?